4S 6200 mAh Nur für H520E

Dämpfergummis (8 Stk.) für CGOET / E50 / CGO3+ Kamera  

  IMU-Modul für H520 / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  Abziehwerkzeug für Motor-LED-Abdeckung für H520 / Typhoon H Plus / H3 Hexacopter   

  Dreifarben LED-Zubehör für H520 / Typhoon H Plus / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  Ein/Aus-Schalter für H520 / Typhoon H Plus / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  GPS-Modul für H520 oder Typhoon H Plus / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  Landegestellplatine für H520 / Typhoon H Plus / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  Micro-USB Adapter für H520 / Typhoon H Plus / H3 Hexacopter   WEEE-Reg.-Nr. DE 78138862

  Motorabdeckung für H520 /  H3 / Typhoon H Plus Hexacopter  

Propeller Sorte "A" für H520 / Typhoon H Plus / H3 Hexacopter  

Propeller Sorte "B" für H520 / Typhoon H Plus / H3 Hexacopter  

  Propeller-Schnellverschluss "A" für H520 / Typhoon H Plus / H3 Hexacopter  

  Propeller-Schnellverschluss "B" für H520 / Typhoon H Plus / H3 Hexacopter  

  SR24 Empfängerplatine für H520 oder Typhoon H Plus / H3 Hexacopter WEEE-Reg.-Nr. DE 78138862    

  Halterung für die Antenne für H520 / Typhoon H Plus / Typhoon H / H3   

  Klickverschluss (Ausleger) für H520 / Typhoon H Plus / Typhoon H / H3 Hexacopter  

  Innerer Rahmen für H520 and Typhoon H Plus Hexacopter  

  Ausleger A (ohne Motor) für H520 Hexacopter  

  Ausleger B (ohne Motor) für H520 Hexacopter  

  ESC-Modul für H520 Hexacopter WEEE-Reg.-Nr. DE 78138862    

MAINTENANCE AFTER 125 HOURS OF FLIGHT TIME With the Maintenance Program, our certified technicians will make sure that your drone is in the right condition to get the best out of your flight operations. This program can be performed on the H520/E and all Typhoon drone series. Services included: Aircraft check: Motor play - lift each motor and add side pressure. Replaced if necessary Propeller locks for integrity, wear and operation. Replace if excessive wear is noticed Venting areas for debris and dust Arm locking mechanism and replace if required Landing gear actuators and check for contact wear and clean Antennas sleeves for any wear, or frayed wires Gimbal rail for any damage, wear or stress marks. Replaced if necessary Camera lens threads for thread integrity Calibration of compass, accelerometer and gimbal All propellers replaced Camera check:  Top mount for wear. Replace if excessive wear is noticed Camera gimbals vibration dampers and replaces as required Tilt, pan, and yaw motors for correct movement Lens damage and report if required ST16 Series Ground Station control check: Vents for debris and dust Switch retainer rings for tightness Secure screws Antennas Battery contacts for engagement Joysticks pivot points and clean   Software:Firmware update on the Aircraft, Ground Station Control and Camera. Flight test:Perform a controllability check flight to ensure correct control of pitch, yaw, roll and altitude. Also, confirm that the landing gear operates correctly. NOTE: After purchasing the service, please send Request an RMA mentioning in the error description: the ordered maintenance package and the order number.  *Return shipment included. 

MAINTENANCE AFTER 175 HOURS OF FLIGHT TIME With the Maintenance Program, our certified technicians will make sure that your drone is in the right condition to get the best out of your flight operations. This program can be performed on the H520/E and all Typhoon drone series. Services included: Aircraft check: Aircraft shell integrity General condition, clean and remove dust and debris Motherboard integrity, corrosion, connections and joints Both leg actuators and connectors for cracks and tight contact All internal connections and solder joints Dirt and debris from GPS module Battery connection board for wear Motor play - lift each motor and add side pressure. Replaced if necessary Propeller locks, wear and operation. Replace if excessive wear is noticed Venting areas for debris and dust Arm locking mechanism and replace if required Landing gear actuators and check for contact wear and clean Antennas sleeves for any wear, or frayed wires Gimbal rail for any damage, wear or stress marks. Replaced if necessary Camera lens threads Camera quick contact pins for wear and clean if necessary Landing gear actuators (remove and assess) and ensure legs are secure Calibration of compass, accelerometer and gimbal Replace of: Arm locks, arm springs, all propellers, Camera gimbal vibration dampers and Gimbal rails-top mount Camera check: E50, E90, CGOET, E10T, E10Tv Top mount for wear. Replace if excessive wear is noticed Camera gimbals vibration dampers and replaces as required Tilt, pan, and yaw motors for correct movement Lens damage and report if required ST16 Series Ground Station control check: Vents for debris and dust Switch retainer rings for tightness Secure screws Antennas Battery contacts for engagement Joysticks pivot points and clean Gimbal control potentiometer Software:Firmware update on the Aircraft, Ground Station Control and Camera. Flight test:Perform a controllability check flight to ensure correct control of pitch, yaw, roll and altitude. Also, confirm that the landing gear operates correctly. NOTE: After purchasing the service, please send Request an RMA mentioning in the error description: the ordered maintenance package and the order number.  *Return shipment included. 

MAINTENANCE AFTER 75 HOURS OF FLIGHT TIME With the Maintenance Program, our certified technicians will make sure that your drone is in the right condition to get the best out of your flight operations. This program can be performed on the H520/E and all Typhoon drone series. Services included: Aircraft check: Aircraft check: Arm locks for positive operation Motor wire sleeves leading into the airframe for wear Propeller: mount screws are secure and each propeller spins freely and not grit or debris inside motor Camera mount for wear damage Battery contacts for engagement Cleaning of arms, landing legs, main body, gimbal and sonar ports Calibration of compass, accelerometer and gimbal Camera check:  Top mount for wear. Replace if excessive wear is noticed Camera gimbals vibration dampers and replaces as required Tilt, pan, and yaw motors for correct movement Lens damage and report if required ST16 Series Ground Station control check: Vents for debris and dust Switch retainer rings for tightness Secure screws Antennas Battery contacts for engagement Joysticks pivot points and clean   Software:Firmware update on the Aircraft, Ground Station Control and Camera. Flight test:Perform a controllability check flight to ensure correct control of pitch, yaw, roll and altitude. Also, confirm that the landing gear operates correctly. NOTE: After purchasing the service, please send Request an RMA mentioning in the error description: the ordered maintenance package and the order number.  *Return shipment included.